fbpx

Flash Photography Basics: Get Your Flash Off Camera!

This is part 7 in the Flash Photography Basics Series.  To start from the beginning, click here.

Flash photography can be useful when the flash is attached to the hotshoe of the camera, but flash photography can absolutely transform your photography once you understand how to use off-camera flash.

Learning how to get the flash to wirelessly fire as the camera takes a picture is probably the most daunting aspect of off-camera flash photography.  This is daunting because there are dozens of different setups for off-camera flash and many different companies creating proprietary technology in the flash photography space.

If you want to simplify this daunting process, I can simply tell you the solution that will only cost you $20 and will work consistently.  It is the way I make my camera fire wirelessly off-camera and the method that I have found to produce reliable results.  If you follow my recommended setup with your YN-560 flash, you can read and apply the following paragraph and then simply SKIP the rest of this article and head to the next article in this series.  If you are a geek like me and want to know all the possible ways to do things, then you have a lot of reading to do 🙂

My Simple Setup for Off-Camera Flash

Yongnuo flash trigger
This is the SIMPLEST way to get your flash to fire off camera even though there are many other options that work well too. Just put one of these on the camera, and one under your flash. DONE!

The setup I recommend is to have one piece of gear (called a flash trigger) that you slip onto the hotshoe of the camera.  This is an inexpensive $20 purchase.  The flash trigger simply sends out a radio signal to any and all flashes within range and tells it when to fire.

Then, you need a way for the flash to receive this message.  A flash receiver is a simple device that connects to the bottom of the flash and tells the flash when to fire based on the information it receives from the trigger on the camera.  If you purchased the YN-560 III that I recommended in the last article (hint, hint!), you do not need a separate device to do this.  It is built in to the flash.

So the simple way to do this is to buy a Yongnuo flash trigger for $20, put it on your camera, and call it a day.  All you need to do is slip one on the hotshoe of the camera and you are done.  No special camera settings.  No slave mode.  No commander mode.  No camera upgrade.  Done.  Simply put the trigger on your camera and it will do the rest.

The flash trigger I recommend actually isn't a trigger at all.  Or, more correctly, it isn't only a trigger.  It is a trigger and receiver in one, which is called a tranceiver.  That is handy because you can put one on the camera to be the trigger, or buy two and use the second one under a flash that doesn't have a built in receiver like the YN-560III does.

For links to buy the tranceiver, YN-560 III, as well as other flash photography items, check out my flash photography gear recommendations (click link and it will open in a separate tab so you can keep reading here).  As a side note, I spent several thousand dollars trying out all kinds of speedlights, umbrellas, light stands, and other flash photography items to put together that list of recommended gear.  I wanted to help you save as much money as possible and still get high quality durable gear that will last you many many years of photography.  I hope you enjoy that list.

You are set!  If you follow my recommended method for off-camera flash, you can skip to the next article in this series here.  You won't need any of the information below.

Other Methods of Triggering Off-Camera Flash

Every camera and flash manufacturer uses their own proprietary technology for firing the flash wirelessly.  If you have different gear than my recommended setup or you prefer to use other technology, the information below should help you get started.

I don't pretend my recommended setup is perfect for everyone, after all.  I only recommend my way of doing it so that new flash photographers can just buy an inexpensive kit that works easily so they can get started.

There are four basic ways to trigger an off camera flash: built-in infrared triggering , dedicated infrared triggering, radio triggers, and using a flash as a slave.

Built-in Infrared Triggering

Some cameras have the capability to trigger a flash built-in to the camera.  This type of system does not require the purchase of a third-party flash trigger or receiver for the camera to get the flash to fire wirelessly.

Unfortunately, not all cameras have this capability and it generally only works in conjunction with a flash unit that is made by the same company as the camera brand.  Most Nikon cameras have this capability built-in.  Some recent Canon DSLRs have this capability as well: for example, the Canon 60D and the Canon 7D.  Some Sony models also have this capability.  The best way to know if your camera can trigger a flash without a dedicated trigger is to check your camera manual.

If your camera model has built-in flash triggering capabilities, you will need to know how to set the camera up to fire the flash wirelessly.  This depends on each camera model, but there are numerous resources online to help.

If you use a Canon camera and own a Canon flash, watch this video for a simple tutorial on how to use the built-in infrared trigger.

If you use a Nikon camera and own a Nikon flash, watch this video for a simple tutorial on how to use the built-in infrared trigger.

If you use a Sony camera and own a Sony flash, watch this video for a simple tutorial on how to use the built-in infrared trigger.

There are many limitations to using the built-in infrared triggering device.  For me, the principal reason not to use this method is that it takes too long to set up, I lack the control to trigger various groups of flashes, and it can only be used to fire flashes that come from the same company as the camera.

I must include a small caveat in my last statement.  There are actually ways to trigger a third-party flash using the built-in infrared capability of your flash; however, I guarantee that trying to do so will cause severe headaches.  It simply isn't worth the trouble.

Dedicated Infrared Triggering

For most photographers, I find this to be the most simple and cost-effective solution to triggering an off-camera flash.  This method involves purchasing a cheap (usually around $20) wireless trigger for your camera, and a receiver to go on your flash.

If you use a Canon, Nikon, Olympus or Pentax DSLR and ANY brand of flash, you can purchase this flash trigger.

If you use a Sony camera and ANY brand flash, you can purchase this flash trigger.

Obviously, there are many other companies that produce infrared flash triggers and receivers for your camera, but I have found that this model that I have linked to is simple to use, works like a charm, and costs less than any other option.

Keep in mind that if you want to trigger multiple flashes at the same time from one camera, you will either need to purchase a flash receiver for each flash (recommended), or you can use receiver on one flash and set the other flashes to slave mode.

Radio Triggering

The radio trigger is the most popular option for triggering off-camera flash among pro photographers.  The advantage to using a radio trigger over an infrared trigger is that it is capable of firing the flash from long distances and it is not susceptible to infrared light interference.

Infrared triggers work great from a distance under 40 feet (12 meters); however, few infrared triggers can consistently trigger a flash from any greater distance.  Also, infrared light can often be interfered with by the ambient light.  For example, it can be difficult to fire a flash using an infrared trigger when shooting at sunset near the bright sun.  The ambient light will often drown out the signal and prevent the signal from being passed from the trigger to the receiver.

Unfortunately, most radio triggers are significantly more expensive than infrared triggers.  The two most common brands of radio triggers are Radio Poppers and Pocket Wizards.  It would seem that Pocket Wizards are slightly more popular among professional photographers than Radio Poppers, but both brands are capable of working quite well.

Most radio triggers do not come as separate triggers for the camera and receivers for the flash.  Most of them are transceivers, which do both the triggering and receiving.  This way you can use any unit on either the DSLR to trigger or the flash to receive the signal.

The trigger in the recommended setup I included above is a radio trigger.

Firing a Flash as a Slave

Almost all flash units come with the capability to fire when the flash unit sees a sudden increase of light.  This is called slave mode.  Slave mode is used when the photographer either uses the pop-up flash or has only one trigger/receiver set, but wishes to fire multiple flashes simultaneously.

Consult the manual for your specific flash to learn how to set it in slave mode.  This is usually a very simple operation.

Many photographers worry that firing a flash in slave mode will cause a delay so that the slave flash does not fire in time before the exposure ends.  This simply isn't the case.  The flash is capable of responding to a burst of light in only a matter of a few milliseconds… much shorter than a typical flash exposure.

The limitation of slave mode is that it can be very difficult for each flash to see the burst of light from another flash, which often produces sporadic and inconsistent results.  The only time I use slave mode is when I'm shooting indoors and I find myself in a pinch without enough flash receivers.

Continue to page 8

18 thoughts on “Flash Photography Basics: Get Your Flash Off Camera!”

  1. Using this style makes betting much more accessible to the public.
    Football has become an exceptionally popular sports within the past decades, which has to be mostly attributed to
    its great fans and supporters. Depending upon the specific
    requirement of the punter, selection can be made of an online betting site; though, preference should be given to the
    site which helps in decision making as a decision based on the information and thorough
    analysis of the probabilities of the teams and their performance
    is of utter importance.

  2. In fact, getting the right plumbers anywhere is a tough job.
    You will need liability insurance in the amount of $100,000 for bodily injury aand $25,
    000 for property damage. Maybe yyou believe that you require replacing your hot water heater.

  3. Going to training, or going to the park to play or even just helpkng by
    following youu around the house or yard keeps them working and active.
    Jetstar does offer a limited business class, but it is of nott to the same quality ass Qantas,
    so that it does not cannibalise sales from
    its parent. n – The prestigious and comprehensive awards
    program, established in 2005, engages with leading corporate, government and non-profit organisations across key industry segments,
    including financial, manufacturing, professional services, energy, telecommunications, construction,
    transport, healthcare, education, food services and retail.

  4. Love this. So true, which is why everyone should make a camera obscura to really understand directionality of light.

    For the new Sony Cameras use Phottix Mitros+ or the Nissin Di700A (and Air commander).

    Just a quick word also for those with eyesight problems, and fast tracking problems… have a look at this. It changed my life. I really believe that if everyone understood how to use this camera, there would be no other cameras. Expensive Nikons, SOLD! http://www.garyfong.com/learn/understanding-auto-focus-sony-mirrorless-cameras

  5. I have the YN-560 III and Yongnuo flash trigger and can’t get it to fire off camera. What settings do I need on the flash?

  6. I have a flash that I use as slave for my D7000, together with the built in flash as master.

    I just bought a basic flash ( Bower SFD958N) that has iTTL mode but does not supports the slave and master.

    Question:
    Can I use this new flash on camera (instead of the bulit-in ) along with my better flash in a slave mode?
    Let me clarify.
    What triggers the Slave flash? The camera or the built in flash?

    1. Hi, Al

      On the D7000 and D7100 as well (I own 1 of these), the only way to trigger the slave flash is ether by firing the build-in flash or by a wireless trigger. It’s like that for most of the Chinese brand flashes (the Yongnuo I believe is an exceptions, because it triggers no mater what light bursts), at least with my Triopo TR586EX is like that.
      I hope I answered your question.

      Kind regards,
      Bobby

  7. In Part 7 under “Built-In Infrared Triggering” it states” If you use a Canon camera and own a Canon flash, watch this video for a simple tutorial on how to use the built-in infrared trigger”. Cannot find this video anywhere on the page.

    Les Moss

  8. On January 25,2016 I posed a question “In Part 7 under “Built-In Infrared Triggering” it states”If you use a Canon camera and own a Canon flash, watch this video for a simple tutorial on how to use the built-in infrared trigger. Cannot find this video anywhere on
    the page”
    It should have read “In Part7 (page 7) under “Dedicated Infrared Triggering it states “If you use a Canon camera and own a Canon flash, watch this video for a simple tutorial on how to use the built-in infrared trigger. Cannot find this video anywhere on
    the page”
    Can anyone help?

  9. Apparently I tried firing my Metz 51AF with the Canon 60D using the built-in infrared trigger and it worked well. Tho the only issue is if the flash unit isn’t within line of sight (ie. used as a back light hidden behind the object), it sometimes doesn’t fires properly. Overall setup wasn’t too bad, u just hv to know which buttons to press.

Leave a Reply to Alan Cancel reply

Your email address will not be published. Required fields are marked *

Scroll to Top